Neuer Flughafen mit Afcad2

[Develop]

rechteckige bereiche würden mir erstmal reichen , da ich mit ground 2k nicht zurecht komme.

[JOBIA]

Hier der Auszug aus dem FS2000 SDK. Da dieses Verfahren im FS2002 funktionierte dürfte es auch im FS2004 noch funktionieren.

Ev. kann es sein das aufgrund des geänderten Airportscodes beim FS2004 das excludieren bei Navigationseinrichtungen nicht mehr funktioniert.

Exclusion and Flattening switches
Some backward-compatible/add-on sceneries may not appear as expected in Flight Simulator 2000. The factors most commonly responsible for such problems are:
· Flight Simulator 2000 uses a digital elevation mesh terrain system instead of the flat "seed" system used in prior versions, and
· Flight Simulator 2000 incorporates nearly every airport and published navigational aid in the entire world.

Flight Simulator 2000 has two "switches" – Flatten and Exclude – that can be used in the Scenery.cfg file to solve a great number of visual problems with backward-compatible/add-on scenery. The Flatten switch flattens a given four-sided area to a single specified elevation. The Exclude switch excludes the default Microsoft scenery (objects and/or navigational aids) in a given four-sided area from being displayed (or transmitted in the case of radio navigational aids).

Both switches affect only scenery areas with a lower layer number than the scenery area they are added in. For example, if the switch is placed in layer 70, then only layers 69 and below will be affected. Switches are added to the end of a scenery area entry in the Scenery.cfg file using a text editor. Exclude and Flatten switches can both be added to the same Scenery area.

Flatten Switch:
The Flatten switch syntax is as follows:
Flatten.X=Elevation,Latitude1,Longitude1,Latitude2 ,Longitude2,Latitude3,Longitude3,Latitude4,Longitu de4
X is equal to a number between 0 and 9, but you must start with Flatten.0, then Flatten.1, and so on, up to Flatten.9. You are allowed a maximum of 10 Flatten switches per Scenery Area (thus the numbers 0-9).
The Elevation is in feet above or below mean sea level (msl) and can be any number between -2000 and 99999.
The Latitude and Longitude of points 1, 2, 3, and 4 must be entered in a clockwise or counter clockwise fashion about the four-sided area such as:

1 +-------------+ 2
| |
| |
| |
4 +-------------+ 3
or

1 +-------------+ 4
| |
| |
| |
2 +-------------+ 3

and must be in the form of degrees and minutes. You do not need to add the * or ' symbols to indicate degrees and minutes, and the shape does not have to be a rectangle. Any four-sided shape will work.
The maximum size of a flattened area is 90 degrees of longitude and 45 degrees of latitude.
The following example flattens two separate but adjacent regions inside the scenery area to an elevation of 1000' MSL.
[Area.100]
Group =Your Area
ID =Your Area
Title =Your Area
Active =TRUE
Layer =100
Local =C:\Your Area
Flatten.0 =1000,N45 30,W120,N45 30,W119 30,N45,W119 30,N45,W120
Flatten.1 =1000,N45,W120,N45,W119 30, N44 30,W119 30,N44 30,W120

Exclude switch

The Exclude switch syntax is as follows:
Exclude=North Latitude,West Longitude, South Latitude, East Longitude, category
Exclusion happens only in a rectangular area such as:

North Latitude
+-------------+
| |
West Longitude | |East Longitude
| |
+-------------+
South Latitude

and must follow the form North Latitude, West Longitude, South Latitude, East Longitude. The Latitude and Longitude entries must be in the form of degrees and minutes. You do not need to add the * or ' symbols to indicate degrees and minutes.
The category determines which default scenery type you choose to exclude in the defined area. There are 4 categories:
objects Excludes all default 3-dimensional buildings and objects as well as airports.
vors Excludes all default VOR and ILS navigational aids
ndbs Excludes all default NDB navigational aids.
all Excludes all default objects and navigational aids
You can use 1 or more categories in an Exclude switch.
The maximum size of an Exclude area is 90 degrees of longitude and 45 degrees of latitude.
The following example excludes all scenery types EXCEPT NDB navigational aids from a rectangular area.

[Area.100]
Group=Your Area
ID=Your Area
Title=Your Area
Active=TRUE
Layer=100
Local=C:\Your Area
Exclude=N45 30,W120,N45,W119 30,objects,vors

[Develop]

ich habe jetzt folgendes einfach in die scenery.cfg unter dokumnte und einstellungen geschrieben:

[Area.100]
Group =Catan
ID =100
Title =Catan
Active =TRUE
Layer =100
Local =Addon Scenery\Catan
Exclude=N51 44.93,E13 42.84,N51 41.67,E13 50.27,objects,vors
Flatten.0 =2000,N51 44.92,E13 41.55,N51 44.92,E13 50.18,N51 42.06,E13 50.18,N51 41.67,E13 43.22

Autogen wird nicht mehr angezeigt, aber das flatten geht nicht. es änder sich gar nix in dieser Region

[JOBIA]

Ändere die Scenery.cfg im Stammverzeichnis des FS2004. Nicht die jenige die Du unter Dokumente und Einstellungen findest.

[JOBIA]

Ich selbst habe den Flattenbefehl nie genutzt da ich mit Polys über Ground2K oder SCC arbeite.

Ich habe momentan keine Zeit das auszutesten aber was auch auffällt das Du den Minutenrest nach dem Punkt mit angegeben hast. Kann sein das dieses nicht zulässig ist bei diesem Befehl. Denn im Beispiel des SDK ist die Auflösung nur Grad Minute.

[Develop]

ich habe den Befehl jetzt in die Scenery.cfg direkt im FS9 Ordner geschrieben und es funktioniert, Danke