HELP with FSDISP and 7digs..... - Seite 2

bwr014 · 28.08.2004, 01:48

Uli,

Thanks for the picture i see that all the pcb's i made where all for nothing because the layout isnt correct as posted on the site...

Would maybe a tip to correct that so people dont spend 1 month on nothing...

Not everyone is a electronic person and count on the information of a site that it will be correct ... (like me)

But this thing with change wires is also not handy so is there anyone that will have a correct pcb layout for the 3 and 5 set digs?

Would be much more handy than this crossing wires again...

Frans

uli2 · 28.08.2004, 15:46

Hi,
please go to downloads at C..?..P..?..S.
There are the correct Datasheet for the 3c Display connector.

No more frust....

regards
uli

bwr014 · 29.08.2004, 04:06

Uli,

You made the nice drawing for me and i try to figure it out... but is there a option that you can put on that drawing you made also the way i have connected now? i understand that the K.. are not on the correct place now but where do i have my K.. now? example you mention K2 needs to be connected to the most right down pin but where do i have my K2 now connected? other words ... with wire goes to what pin now? you showed me now the correct one with that drawing but now the question is for me where i find the K1 t/m K5 on the pcb i made?

gr.

Frans

bwr014 · 29.08.2004, 17:28

Uli,

Is this making any sence?

http://www.planesonline.nl/images/DSC01534.JPG

Frans

uli2 · 29.08.2004, 19:10

Hi,
thats is the right one !!!!

Yours not correct.

Regards ULI

bwr014 · 29.08.2004, 22:52

what about this Uli?

http://www.planesonline.nl/images/DSC01539.JPG

Frans

uli2 · 29.08.2004, 23:13

Ok,
Take a look to the picture....

regards
Uli

bwr014 · 29.08.2004, 23:24

Uli,

I see the picture... i understand that the leds get on top and you want to connector at the bottom..

i am sorry, dont understand what i did wrong ....

Frans

uli2 · 29.08.2004, 23:29

Hi,
at this time is nothing wrong....

You must solder the parts we at ....example, at picture.

When you put the connector on Top from the board.....then you have also the wrong results !

Make your boards with this layout and put the parts as the last picture...and all is good.

regards
ULI

bwr014 · 29.08.2004, 23:32

.... ok

will give it a try...

But if i want also the connector at the top.. how is the situation than? will be not easy to solder the connector now from the bottom...

Frans

(sorry, very new in this drawing thing... ( more like today started) so i hope not that bad .... )

Frans

28.08.2004, 15:46	#12
uli2 Hero Registriert seit: 10.12.2000 Beiträge: 962	Datasheet ! Hi, please go to downloads at C..?..P..?..S. There are the correct Datasheet for the 3c Display connector. No more frust.... regards uli ____________________________________ Wenn ich nen Tip gebe für XYZ, dann hat das nichts mit Werbung zu tun.

29.08.2004, 19:10	#15
uli2 Hero Registriert seit: 10.12.2000 Beiträge: 962	.... Hi, thats is the right one !!!! Yours not correct. Regards ULI ____________________________________ Wenn ich nen Tip gebe für XYZ, dann hat das nichts mit Werbung zu tun.

29.08.2004, 23:13	#17
uli2 Hero Registriert seit: 10.12.2000 Beiträge: 962	.... Ok, Take a look to the picture.... regards Uli ____________________________________ Wenn ich nen Tip gebe für XYZ, dann hat das nichts mit Werbung zu tun.

29.08.2004, 23:29	#19
uli2 Hero Registriert seit: 10.12.2000 Beiträge: 962	.... Hi, at this time is nothing wrong.... You must solder the parts we at ....example, at picture. When you put the connector on Top from the board.....then you have also the wrong results ! Make your boards with this layout and put the parts as the last picture...and all is good. regards ULI ____________________________________ Wenn ich nen Tip gebe für XYZ, dann hat das nichts mit Werbung zu tun.

28.08.2004, 01:48	#11
bwr014 Veteran Registriert seit: 17.07.2004 Beiträge: 331	Uli, Thanks for the picture i see that all the pcb's i made where all for nothing because the layout isnt correct as posted on the site... Would maybe a tip to correct that so people dont spend 1 month on nothing... Not everyone is a electronic person and count on the information of a site that it will be correct ... (like me) But this thing with change wires is also not handy so is there anyone that will have a correct pcb layout for the 3 and 5 set digs? Would be much more handy than this crossing wires again... Frans

29.08.2004, 04:06	#13
bwr014 Veteran Registriert seit: 17.07.2004 Beiträge: 331	Uli, You made the nice drawing for me and i try to figure it out... but is there a option that you can put on that drawing you made also the way i have connected now? i understand that the K.. are not on the correct place now but where do i have my K.. now? example you mention K2 needs to be connected to the most right down pin but where do i have my K2 now connected? other words ... with wire goes to what pin now? you showed me now the correct one with that drawing but now the question is for me where i find the K1 t/m K5 on the pcb i made? gr. Frans

29.08.2004, 17:28	#14
bwr014 Veteran Registriert seit: 17.07.2004 Beiträge: 331	Uli, Is this making any sence? http://www.planesonline.nl/images/DSC01534.JPG Frans

29.08.2004, 22:52	#16
bwr014 Veteran Registriert seit: 17.07.2004 Beiträge: 331	what about this Uli? http://www.planesonline.nl/images/DSC01539.JPG Frans

29.08.2004, 23:24	#18
bwr014 Veteran Registriert seit: 17.07.2004 Beiträge: 331	Uli, I see the picture... i understand that the leds get on top and you want to connector at the bottom.. i am sorry, dont understand what i did wrong .... Frans

29.08.2004, 23:32	#20
bwr014 Veteran Registriert seit: 17.07.2004 Beiträge: 331	.... ok will give it a try... But if i want also the connector at the top.. how is the situation than? will be not easy to solder the connector now from the bottom... Frans (sorry, very new in this drawing thing... ( more like today started) so i hope not that bad .... ) Frans

Aktive Benutzer in diesem Thema: 1 (Registrierte Benutzer: 0, Gäste: 1)