DIRKAN = Dirk Anderseck

[bwr014]

Can anyone tell me if this is correct? That the screenname dirkan= Dirk Anderseck?

gr.

Frans M

[A319]

I think you are right

Hannes

[bwr014]

You think? hmmm i notice about 100 ppl have looked to this message on the forum and noone can tell me how to contact Dirk or know what his screenname is? His email adress on the FSbus site is not working or he doesnt reply back

Found it i a bit strange that if Dirkan is Dirk that he do reply on a message of DUTCH but not on any FSbus question here???

So it would be very kind of Dirk if he can contact me to see if some questions about FSbus can be solved so that we and help a lot of ppl here as well direct than....

gr.

Frans M

[uli2]

dear frans M.
Dirk is work hard.
Tell us here at forum or at (see link) Mathew your questions about FSBUS.

He can help you, he makes the PCb Boards and he has programmed the config for FSbus and also...compatibel with other hardware and Software to FSBUS.

regards.
Uli
sorry for the incorrect englisch.....but i hope you understand my letters.

[dirkan]

Hallo,

hier bin ich. Ich halte mich in der Tat momentan im Forum etwas zurück, damit ich Zeit für einige Neuerungen habe.
Die Entwicklung kostet halt Zeit.

- neues multifunktionales IO Board mit 64 button, 16LED out, 8 Analog In, 8 Analog Out(PWM) mit einem ATMEGA8535. Das löst die Beschaffungsproblematik und den Preis der ADC0808.

- neues COM Board mit Flash für PonyProg Software. Ein ursprünglich geplantes USB Interface habe ich wieder verworfen, da dieses einfach mit einem Kabel USB Adapter gelöst werden kann.

- neues Display mit Brightness Control, decimal Point Control

Keine Angst, für einen parallel Lauf mit dem alten FSBUS wird gesorgt.

Noch ein Hinweis: Das Servo Board lässt hin und wieder die Servos zucken. Je nach Typ mehr oder weniger stark. Ich versuche das auch mit einem Neuentwurf mit leistungsfähigeren Micros zu lösen.

Betatests laufen momentan.

So und nun wünsche ich Frohe Weihnacht

Dirk

[bwr014]

Uli,

Thanks for your response.. and your english is fine i understand it no problem.

only be a bit lost with what you mean (link) What link you mean?

THEN...

I am sorry to say that i already use this forum with a lot of questions and there is no reponse on it at all from any programmer and i think that is not correct!

I already have try to do a lot myself and manage some things with offsets and also have been talking to the people of PM and HCSTD and Pete Downson for offsets but in some things we need more help and my idea was that this is the forum to get it...

I understand that everyone have there own things and is of course busy and i am not asking to change that but i see now a lot of questions beside the ones i ask here about FSbus that arent answerd... i even get mails now for help and i always be there to help people as well with things i know but also for me some things are not clear and it would be than very kind to get some help from the ones that know how to do that.

I assum that also the one that do the programming see this forum and questions of me as well .... why dont i get any response on that one or just a response back when i send a email even if it would be with sorry no time to help you now so i know iam dont send it to noone....

but ok let me know who i need to contact to try to solve my questions? That would help me a lot to continue here as well and maybe help others also again

Gr

Frans M

[stevelep]

Thank's Dirk for these good news ...

I've transmit and translate your post in english on the avsim forum
Everybody is happy and excited to see the new features ....

And have ask me to thank's you

Merry Christmas & Happy new Year

Bye

Steve

Auf Deutsch:

Danke Dirk
Ich habe deine Post zum Avsim Forum in English ubersetzt
Alle Leute sind froh und ungeduldig die neue Funktionen zu probieren ...

Und habe mir gefragt dir zu danken für deine super Arbeit

Schöne Weinachten