FSBus-Spezialisten

pmartin · 19.12.2004, 11:30

Hallo Leute,
wer findet den Fehler? Ich versteh es nicht!

0, "HCSDT"
1, "OHL_LED", 510, 0, 0x04645, I16,,R, 10,1,1,
2, "APU MASTER ON LED", 511, 0, 0, BIT, 0, R ,10,1,1,
2, "APU MASTER FAULT LED", 512, 0, 0, BIT, 1, R ,10,1,1,
2, "APU START ON LED", 513, 0, 0, BIT, 2, R ,10,1,1,
2, "APU START AVAIL LED", 514, 0, 0, BIT, 3, R ,10,1,1,
2, "HYD1 PUMP OFF LED", 515, 0, 0, BIT, 4, R ,10,1,1,
2, "HYD1 PUMP FAULT LED", 516, 0, 0, BIT, 5, R ,10,1,1,
2, "HYD2 PUMP OFF LED", 517, 0, 0, BIT, 6, R ,10,1,1,
2, "HYD2 PUMP FAULT LED", 518, 0, 0, BIT, 7, R ,10,1,1,

1, "OHL_SW", 519, 0, 0x04602, I16,,W, 10,1,1,
2, "APU MASTER TOGGLE", 520, 0, 0, BIT, 33, W ,10,1,1,
2, "APU START ON", 521, 0, 0, BIT, 36, W ,10,1,1,

Ich kann zwar (siehe beiliegende FSBUS.fb2) den Zustanwechsel der LED sehen, die Steuerung mit den Schalter klappt aber nicht!
Wer hat ne Idee woran es liegen könnte?

Gruss Peter
P.S. Schönen 4. Advent!

bwr014 · 19.12.2004, 15:09

Hi Peter,

Uhm...

BIT, 33 ?
BIT, 36 ?

That is not possible i think you have to keep it to 0-7 or you need to change i think the I16 in a bigger nummer...

Try to give them as well BIT,1 and BIT,2 with the offset 4602...

gr.

Frans

pmartin · 19.12.2004, 15:21

=>>> e-mail

pmartin · 21.12.2004, 11:50

Schade hat keiner ne Idee wie das gehen könnte?

Gruss Peter

pmartin · 23.12.2004, 22:58

DIRK bitte helfen!

Gruss Peter

dirkan · 23.12.2004, 23:46

Hallo Peter,

wo kommt denn die .fb2 Datei her ? Ich habe meine Platte durchsucht
aber nix mit APU gefunden. Kann mich auch nicht erinnern, da jemals
was mit gemacht zu haben.

Bitte mehr Infos, woher die Datei mit diesen Einträgen kommt udn
was für einen Flieger (AddON, PM oä.) du verwendest.

Gruss Dirk

dirkan · 24.12.2004, 00:03

Habe mal die Docs von HCSDT angeschaut.
Einen Offset 4602 habe ich nirgends gesehen.

???

Woher kommt die Info, dass da was stehen soll.

Bit 33 und 36 gehen garantiert nicht, da fsbus max. 32 Bit
verwendet.

Gruss Dirk

bwr014 · 24.12.2004, 02:07

Hello Dirk,

Yes that was also my problem.... it is not possible i think to approche it that way... bits until 0-7 will maybe work... i am going to contact one of the programmers of HCSTD as well and try to figure it out... keep you updated.

Frans M

EDXF · 26.12.2004, 12:33

Es handelt sich um diese Doku.

Diese ist mit der Build 91 der OHL mitgeliefert worden.
Hier werden keine bits gesetzt sondern Werte in ein byte langes FSUIPC offset geschrieben. OFFSET HEX 4602.

- NEW OFFSET PIPE FOR FSUIPC CONTROL
Send this values into the byte address 4602.
Write only if byte is 0. Will be set 0 by the OHL.
1 = SIM RUN TOGGLE

2 = MAINTENANCE

3 = AC ESS FEED TOGGLE
4 = AC ESS ON
5 = AC ESS OFF

6 = GALLEY TOGGLE
7 = GALLEY ON
8 = GALLEY OFF

9 = BAT 1 TOGGLE
10 = BAT 1 ON
11 = BAT 1 OFF

12 = BAT 2 TOGGLE
13 = BAT 2 ON
14 = BAT 2 OFF

15 = GEN 1 TOGGLE
16 = GEN 1 ON
17 = GEN 1 OFF

18 = GEN 2 TOGGLE
19 = GEN 2 ON
20 = GEN 2 OFF

21 = BUS TIE TOGGLE
22 = BUS TIE ON
23 = BUS TIE OFF

24 = EXT PWR TOGGLE
25 = EXT PWR ON
26 = EXT PWR OFF

27 = IDG 1 TOGGLE
28 = IDG 1 ON
29 = IDG 1 OFF

30 = IDG 2 TOGGLE
31 = IDG 2 ON
32 = IDG 2 OFF

33 = APU MASTER TOGGLE
34 = APU MASTER ON
35 = APU MASTER OFF
36
37 = APU START ON
38
39

40 = APU GEN TOGGLE
41 = APU GEN ON
42 = APU GEN OFF

43 = APU BLEED TOGGLE
44 = APU BLEED ON
45 = APU BLEED OFF

46 = ENG 1 BLEED TOGGLE
47 = ENG 1 BLEED ON
48 = ENG 1 BLEED OFF

49 = ENG 2 BLEED TOGGLE
50 = ENG 2 BLEED ON
51 = ENG 2 BLEED OFF

52 = X BLEED TOGGLE
53 = X BLEED AUTO
54 = X BLEED OPEN
55 = X BLEED CLOSE

56 = BLUE HYD TOGGLE
57 = BLUE HYD ON
58 = BLUE HYD OFF

59 = GREEN HYD TOGGLE
60 = GREEN HYD ON
61 = GREEN HYD OFF

62 = YELLOW HYD TOGGLE
63 = YELLOW HYD ON
64 = YELLOW HYD OFF

65 = YELLOW ELEC HYD TOGGLE
66 = YELLOW ELEC HYD ON
67 = YELLOW ELEC HYD OFF

68 = HYD PTU TOGGLE
69 = HYD PTU ON
70 = HYD PTU OFF

71 = PACK 1 TOGGLE
72 = PACK 1 ON
73 = PACK 1 OFF

74 = PACK 2 TOGGLE
75 = PACK 2 ON
76 = PACK 2 OFF

77 = ON SMKOE SIGN OFF
78 = ON SMKOE SIGN ON
79 = ON SMKOE SIGN AUTO

80 = FASTEN SEAT BELTS ON
81 = FASTEN SEAT BELTS OFF
82 = FASTEN SEAT BELTS AUTO

83 = LEFT TANK PUMP 1 TOGGLE
84 = LEFT TANK PUMP 1 ON
85 = LEFT TANK PUMP 1 OFF
86 = LEFT TANK PUMP 2 TOGGLE
87 = LEFT TANK PUMP 2 ON
88 = LEFT TANK PUMP 2 OFF

89 = RIGHT TANK PUMP 1 TOGGLE
90 = RIGHT TANK PUMP 1 ON
91 = RIGHT TANK PUMP 1 OFF
92 = RIGHT TANK PUMP 2 TOGGLE
93 = RIGHT TANK PUMP 2 ON
94 = RIGHT TANK PUMP 2 OFF

95 = CENTER TANK PUMP 1 TOGGLE
96 = CENTER TANK PUMP 1 ON
97 = CENTER TANK PUMP 1 OFF
98 = CENTER TANK PUMP 2 TOGGLE
99 = CENTER TANK PUMP 2 ON
100 =CENTER TANK PUMP 2 OFF

101 = FUEL MODE SEL TOGGLE
102 = FUEL MODE SEL ON
103 = FUEL MODE SEL OFF
104 = FUEL XFEED TOGGLE
105 = FUEL XFEED NO
106 = FUEL XFEED OFF

107 = WING ANTIICE TOGGLE
108 = WING ANTIICE ON
109 = WING ANTIICE OFF

110 = ENG 1 AICE TOGGLE
111 = ENG 1 AICE ON
112 = ENG 1 AICE OFF

113 = ENG 2 AICE TOGGLE
114 = ENG 2 AICE ON
115 = ENG 2 AICE OFF

116 = PROBE HEAT TOGGLE
117 = PROBE HEAT ON
118 = PROBE HEAT OFF

119 = GPWS SYS TOGGLE
120 = GPWS SYS ON
121 = GPWS SYS OFF

122 = GPWS GS MODE TOGGLE
123 = GPWS GS MODE ON
124 = GPWS GS MODE OFF

125 = GPWS FLAP MODE TOGGLE
125 = GPWS FLAP MODE ON
125 = GPWS FLAP MODE OFF

128 = GPWS LDG 3 TOGGLE
129 = GPWS LDG 3 ON
130 = GPWS LDG 3 OFF

131
132
133
134
135
136
137
138
139

140 = ELAC 1 TOGGLE
141 = ELAC 1 ON
142 = ELAC 1 OFF

143 = ELAC 2 TOGGLE
144 = ELAC 2 ON
145 = ELAC 2 OFF

146 = SEC 1 TOGGLE
147 = SEC 1 ON
148 = SEC 1 OFF

149 = SEC 2 TOGGLE
150 = SEC 2 ON
151 = SEC 2 OFF

152 = SEC 3 TOGGLE
153 = SEC 3 ON
154 = SEC 3 OFF

155 = FAC 1 TOGGLE
156 = FAC 1 ON
157 = FAC 1 OFF

158 = FAC 2 TOGGLE
159 = FAC 2 ON
160 = FAC 2 OFF

161
162
163
164
165
166
167
168
169

170 = REFUEL PWR TOGGLE
171 = REFUEL PWR ON
172 = REFUEL PWR OFF

173 = REFUEL CTR TOGGLE
174 = REFUEL CTR ON
175 = REFUEL CTR OFF

176 = REFUEL FUEL INC
177 = REFUEL FUEL DEC

180 = MASTER WARNING PRESS

181 = MASTER CAUTION PRESS

182 = GPWS WARNING PRESS

190 = IRS 1 OFF
191 = IRS 1 NAV
192 = IRS 1 ATT

193 = IRS 2 OFF
194 = IRS 2 NAV
195 = IRS 2 ATT

196 = IRS 3 OFF
197 = IRS 3 NAV
198 = IRS 3 ATT

200 = ADR 1 TOGGLE
201 = ADR 1 ON
202 = ADR 1 OFF

203 = ADR 2 TOGGLE
204 = ADR 2 ON
205 = ADR 2 OFF

206 = ADR 3 TOGGLE
207 = ADR 3 ON
208 = ADR 3 OFF

210 APU FIRE TEST
211 ENG 1 FIRE TEST
212 ENG 2 FIRE TEST

240 CIRCUIT BRAKER (FAULT COMPUTER)

Gruß Holger

pmartin · 26.12.2004, 13:06

Sind das dann die Werte (z.B. 210 für APU FIRE TEST)die ich in das Feld Value beim FSBus eintrage?

Gruss Peter

19.12.2004, 11:30	#1
pmartin Elite Registriert seit: 26.06.2002 Alter: 59 Beiträge: 1.153	FSBus-Spezialisten Hallo Leute, wer findet den Fehler? Ich versteh es nicht! 0, "HCSDT" 1, "OHL_LED", 510, 0, 0x04645, I16,,R, 10,1,1, 2, "APU MASTER ON LED", 511, 0, 0, BIT, 0, R ,10,1,1, 2, "APU MASTER FAULT LED", 512, 0, 0, BIT, 1, R ,10,1,1, 2, "APU START ON LED", 513, 0, 0, BIT, 2, R ,10,1,1, 2, "APU START AVAIL LED", 514, 0, 0, BIT, 3, R ,10,1,1, 2, "HYD1 PUMP OFF LED", 515, 0, 0, BIT, 4, R ,10,1,1, 2, "HYD1 PUMP FAULT LED", 516, 0, 0, BIT, 5, R ,10,1,1, 2, "HYD2 PUMP OFF LED", 517, 0, 0, BIT, 6, R ,10,1,1, 2, "HYD2 PUMP FAULT LED", 518, 0, 0, BIT, 7, R ,10,1,1, 1, "OHL_SW", 519, 0, 0x04602, I16,,W, 10,1,1, 2, "APU MASTER TOGGLE", 520, 0, 0, BIT, 33, W ,10,1,1, 2, "APU START ON", 521, 0, 0, BIT, 36, W ,10,1,1, Ich kann zwar (siehe beiliegende FSBUS.fb2) den Zustanwechsel der LED sehen, die Steuerung mit den Schalter klappt aber nicht! Wer hat ne Idee woran es liegen könnte? Gruss Peter P.S. Schönen 4. Advent!

26.12.2004, 12:33	#9
EDXF Veteran Registriert seit: 22.08.2000 Alter: 62 Beiträge: 318	HCSDT Offset Es handelt sich um diese Doku. Diese ist mit der Build 91 der OHL mitgeliefert worden. Hier werden keine bits gesetzt sondern Werte in ein byte langes FSUIPC offset geschrieben. OFFSET HEX 4602. - NEW OFFSET PIPE FOR FSUIPC CONTROL Send this values into the byte address 4602. Write only if byte is 0. Will be set 0 by the OHL. 1 = SIM RUN TOGGLE 2 = MAINTENANCE 3 = AC ESS FEED TOGGLE 4 = AC ESS ON 5 = AC ESS OFF 6 = GALLEY TOGGLE 7 = GALLEY ON 8 = GALLEY OFF 9 = BAT 1 TOGGLE 10 = BAT 1 ON 11 = BAT 1 OFF 12 = BAT 2 TOGGLE 13 = BAT 2 ON 14 = BAT 2 OFF 15 = GEN 1 TOGGLE 16 = GEN 1 ON 17 = GEN 1 OFF 18 = GEN 2 TOGGLE 19 = GEN 2 ON 20 = GEN 2 OFF 21 = BUS TIE TOGGLE 22 = BUS TIE ON 23 = BUS TIE OFF 24 = EXT PWR TOGGLE 25 = EXT PWR ON 26 = EXT PWR OFF 27 = IDG 1 TOGGLE 28 = IDG 1 ON 29 = IDG 1 OFF 30 = IDG 2 TOGGLE 31 = IDG 2 ON 32 = IDG 2 OFF 33 = APU MASTER TOGGLE 34 = APU MASTER ON 35 = APU MASTER OFF 36 37 = APU START ON 38 39 40 = APU GEN TOGGLE 41 = APU GEN ON 42 = APU GEN OFF 43 = APU BLEED TOGGLE 44 = APU BLEED ON 45 = APU BLEED OFF 46 = ENG 1 BLEED TOGGLE 47 = ENG 1 BLEED ON 48 = ENG 1 BLEED OFF 49 = ENG 2 BLEED TOGGLE 50 = ENG 2 BLEED ON 51 = ENG 2 BLEED OFF 52 = X BLEED TOGGLE 53 = X BLEED AUTO 54 = X BLEED OPEN 55 = X BLEED CLOSE 56 = BLUE HYD TOGGLE 57 = BLUE HYD ON 58 = BLUE HYD OFF 59 = GREEN HYD TOGGLE 60 = GREEN HYD ON 61 = GREEN HYD OFF 62 = YELLOW HYD TOGGLE 63 = YELLOW HYD ON 64 = YELLOW HYD OFF 65 = YELLOW ELEC HYD TOGGLE 66 = YELLOW ELEC HYD ON 67 = YELLOW ELEC HYD OFF 68 = HYD PTU TOGGLE 69 = HYD PTU ON 70 = HYD PTU OFF 71 = PACK 1 TOGGLE 72 = PACK 1 ON 73 = PACK 1 OFF 74 = PACK 2 TOGGLE 75 = PACK 2 ON 76 = PACK 2 OFF 77 = ON SMKOE SIGN OFF 78 = ON SMKOE SIGN ON 79 = ON SMKOE SIGN AUTO 80 = FASTEN SEAT BELTS ON 81 = FASTEN SEAT BELTS OFF 82 = FASTEN SEAT BELTS AUTO 83 = LEFT TANK PUMP 1 TOGGLE 84 = LEFT TANK PUMP 1 ON 85 = LEFT TANK PUMP 1 OFF 86 = LEFT TANK PUMP 2 TOGGLE 87 = LEFT TANK PUMP 2 ON 88 = LEFT TANK PUMP 2 OFF 89 = RIGHT TANK PUMP 1 TOGGLE 90 = RIGHT TANK PUMP 1 ON 91 = RIGHT TANK PUMP 1 OFF 92 = RIGHT TANK PUMP 2 TOGGLE 93 = RIGHT TANK PUMP 2 ON 94 = RIGHT TANK PUMP 2 OFF 95 = CENTER TANK PUMP 1 TOGGLE 96 = CENTER TANK PUMP 1 ON 97 = CENTER TANK PUMP 1 OFF 98 = CENTER TANK PUMP 2 TOGGLE 99 = CENTER TANK PUMP 2 ON 100 =CENTER TANK PUMP 2 OFF 101 = FUEL MODE SEL TOGGLE 102 = FUEL MODE SEL ON 103 = FUEL MODE SEL OFF 104 = FUEL XFEED TOGGLE 105 = FUEL XFEED NO 106 = FUEL XFEED OFF 107 = WING ANTIICE TOGGLE 108 = WING ANTIICE ON 109 = WING ANTIICE OFF 110 = ENG 1 AICE TOGGLE 111 = ENG 1 AICE ON 112 = ENG 1 AICE OFF 113 = ENG 2 AICE TOGGLE 114 = ENG 2 AICE ON 115 = ENG 2 AICE OFF 116 = PROBE HEAT TOGGLE 117 = PROBE HEAT ON 118 = PROBE HEAT OFF 119 = GPWS SYS TOGGLE 120 = GPWS SYS ON 121 = GPWS SYS OFF 122 = GPWS GS MODE TOGGLE 123 = GPWS GS MODE ON 124 = GPWS GS MODE OFF 125 = GPWS FLAP MODE TOGGLE 125 = GPWS FLAP MODE ON 125 = GPWS FLAP MODE OFF 128 = GPWS LDG 3 TOGGLE 129 = GPWS LDG 3 ON 130 = GPWS LDG 3 OFF 131 132 133 134 135 136 137 138 139 140 = ELAC 1 TOGGLE 141 = ELAC 1 ON 142 = ELAC 1 OFF 143 = ELAC 2 TOGGLE 144 = ELAC 2 ON 145 = ELAC 2 OFF 146 = SEC 1 TOGGLE 147 = SEC 1 ON 148 = SEC 1 OFF 149 = SEC 2 TOGGLE 150 = SEC 2 ON 151 = SEC 2 OFF 152 = SEC 3 TOGGLE 153 = SEC 3 ON 154 = SEC 3 OFF 155 = FAC 1 TOGGLE 156 = FAC 1 ON 157 = FAC 1 OFF 158 = FAC 2 TOGGLE 159 = FAC 2 ON 160 = FAC 2 OFF 161 162 163 164 165 166 167 168 169 170 = REFUEL PWR TOGGLE 171 = REFUEL PWR ON 172 = REFUEL PWR OFF 173 = REFUEL CTR TOGGLE 174 = REFUEL CTR ON 175 = REFUEL CTR OFF 176 = REFUEL FUEL INC 177 = REFUEL FUEL DEC 180 = MASTER WARNING PRESS 181 = MASTER CAUTION PRESS 182 = GPWS WARNING PRESS 190 = IRS 1 OFF 191 = IRS 1 NAV 192 = IRS 1 ATT 193 = IRS 2 OFF 194 = IRS 2 NAV 195 = IRS 2 ATT 196 = IRS 3 OFF 197 = IRS 3 NAV 198 = IRS 3 ATT 200 = ADR 1 TOGGLE 201 = ADR 1 ON 202 = ADR 1 OFF 203 = ADR 2 TOGGLE 204 = ADR 2 ON 205 = ADR 2 OFF 206 = ADR 3 TOGGLE 207 = ADR 3 ON 208 = ADR 3 OFF 210 APU FIRE TEST 211 ENG 1 FIRE TEST 212 ENG 2 FIRE TEST 240 CIRCUIT BRAKER (FAULT COMPUTER) Gruß Holger

19.12.2004, 15:09	#2
bwr014 Veteran Registriert seit: 17.07.2004 Beiträge: 331	Hi Peter, Uhm... BIT, 33 ? BIT, 36 ? That is not possible i think you have to keep it to 0-7 or you need to change i think the I16 in a bigger nummer... Try to give them as well BIT,1 and BIT,2 with the offset 4602... gr. Frans

19.12.2004, 15:21	#3
pmartin Elite Registriert seit: 26.06.2002 Alter: 59 Beiträge: 1.153	=>>> e-mail

21.12.2004, 11:50	#4
pmartin Elite Registriert seit: 26.06.2002 Alter: 59 Beiträge: 1.153	Schade hat keiner ne Idee wie das gehen könnte? Gruss Peter

23.12.2004, 22:58	#5
pmartin Elite Registriert seit: 26.06.2002 Alter: 59 Beiträge: 1.153	DIRK bitte helfen! Gruss Peter

23.12.2004, 23:46	#6
dirkan Master Registriert seit: 14.02.2002 Alter: 66 Beiträge: 644	Hallo Peter, wo kommt denn die .fb2 Datei her ? Ich habe meine Platte durchsucht aber nix mit APU gefunden. Kann mich auch nicht erinnern, da jemals was mit gemacht zu haben. Bitte mehr Infos, woher die Datei mit diesen Einträgen kommt udn was für einen Flieger (AddON, PM oä.) du verwendest. Gruss Dirk

24.12.2004, 00:03	#7
dirkan Master Registriert seit: 14.02.2002 Alter: 66 Beiträge: 644	Habe mal die Docs von HCSDT angeschaut. Einen Offset 4602 habe ich nirgends gesehen. ??? Woher kommt die Info, dass da was stehen soll. Bit 33 und 36 gehen garantiert nicht, da fsbus max. 32 Bit verwendet. Gruss Dirk

24.12.2004, 02:07	#8
bwr014 Veteran Registriert seit: 17.07.2004 Beiträge: 331	Hello Dirk, Yes that was also my problem.... it is not possible i think to approche it that way... bits until 0-7 will maybe work... i am going to contact one of the programmers of HCSTD as well and try to figure it out... keep you updated. Frans M

26.12.2004, 13:06	#10
pmartin Elite Registriert seit: 26.06.2002 Alter: 59 Beiträge: 1.153	Sind das dann die Werte (z.B. 210 für APU FIRE TEST)die ich in das Feld Value beim FSBus eintrage? Gruss Peter

Aktive Benutzer in diesem Thema: 1 (Registrierte Benutzer: 0, Gäste: 1)