FS key problem

Jan 737 · 02.11.2005, 11:33

Hi,

I add the third fskey card (CID 3 )to my fsbus system.

But there is a problem:
No problems with separate switches, but when I add a 12-stage rotary then strange things happens.Turning the rotary,for changing the nav1 freq.,sets the spoilers to 100%, flaps goes down,N1 increase.
No matter on what RID I connect the rotary.
Chanched the rotary for another, same problem occurs.

Any idea what can cause this?

Bets regards
Jan Geurtsen

Pantu · 02.11.2005, 16:35

Hi Jan,

did you wire the 12 stage rotary as rotary? Also the Switch type should be selected for 12 stage rotary. Can´t think of any thing else causing such strange effect.

Hope it helps.

BTW:
I, myself never used the 12 stage rotaries, but the Alps (same system like Knitter but metal construction) and no problem. Luckily I found a source here in Munich, a kind of surplus shop, where you can get those rotaries incl. a push in switch for about 1 € each.
They are small and work like a charme.

Best rgds

Peter

Jan 737 · 02.11.2005, 16:59

Hi Peter,
Thanks for the answer, yes I checked that.
The setup is good but the problem exist.

About the Alps, are you using them separate or as a dual concentric?

Is it posible to buy 10 Alps for me and send them to Holland?

Best regards

Jan Geurtsen

Pantu · 02.11.2005, 20:08

Hi Jan,

both, the Alps as well as Knitter have a too thin shaft (4mm)to use them as dual concentric. I done it with 2 knitters using a 90 degree gear made out of 2 tooth wheels. So both rotaries are 90 degrees mechanically shifted.
Of course could get you ten of and send them to Holland.

Will try to get downtown tomorrow to buy ´em.

Just let me know where to ship.

Best rgds

Peter

Jan 737 · 02.11.2005, 20:51

Thanks Peter,

Do you have a picture of it.
Is it possible to connect the Alps direct to the key board?

Send me your e-mail address, please.

Best regards

Jan Geurtsen.

Pantu · 03.11.2005, 09:16

Hi Jan,

here´s the picture. Yes, you can directly connect it to the keyboard or FSBus etc.
It works like 2 turn dependant switches. Plus the push in switch on the shaft.

Check your pm for my e-mail address.

Best rgds

Peter

02.11.2005, 11:33	#1
Jan 737 Senior Member Registriert seit: 03.04.2003 Alter: 65 Beiträge: 113	FS key problem Hi, I add the third fskey card (CID 3 )to my fsbus system. But there is a problem: No problems with separate switches, but when I add a 12-stage rotary then strange things happens.Turning the rotary,for changing the nav1 freq.,sets the spoilers to 100%, flaps goes down,N1 increase. No matter on what RID I connect the rotary. Chanched the rotary for another, same problem occurs. Any idea what can cause this? Bets regards Jan Geurtsen

02.11.2005, 16:35	#2
Pantu Master Registriert seit: 11.01.2001 Beiträge: 798	Hi Jan, did you wire the 12 stage rotary as rotary? Also the Switch type should be selected for 12 stage rotary. Can´t think of any thing else causing such strange effect. Hope it helps. BTW: I, myself never used the 12 stage rotaries, but the Alps (same system like Knitter but metal construction) and no problem. Luckily I found a source here in Munich, a kind of surplus shop, where you can get those rotaries incl. a push in switch for about 1 € each. They are small and work like a charme. Best rgds Peter ____________________________________ Immer 3 Grüne Pantu

02.11.2005, 20:08	#4
Pantu Master Registriert seit: 11.01.2001 Beiträge: 798	Hi Jan, both, the Alps as well as Knitter have a too thin shaft (4mm)to use them as dual concentric. I done it with 2 knitters using a 90 degree gear made out of 2 tooth wheels. So both rotaries are 90 degrees mechanically shifted. Of course could get you ten of and send them to Holland. Will try to get downtown tomorrow to buy ´em. Just let me know where to ship. Best rgds Peter ____________________________________ Immer 3 Grüne Pantu

03.11.2005, 09:16	#6
Pantu Master Registriert seit: 11.01.2001 Beiträge: 798	Hi Jan, here´s the picture. Yes, you can directly connect it to the keyboard or FSBus etc. It works like 2 turn dependant switches. Plus the push in switch on the shaft. Check your pm for my e-mail address. Best rgds Peter ____________________________________ Immer 3 Grüne Pantu

Themen-Optionen
Druckbare Version zeigen Jemanden per E-Mail auf dieses Thema hinweisen
Ansicht
Linear-Darstellung Zur Hybrid-Darstellung wechseln Zur Baum-Darstellung wechseln

02.11.2005, 16:59	#3
Jan 737 Senior Member Registriert seit: 03.04.2003 Alter: 65 Beiträge: 113	Hi Peter, Thanks for the answer, yes I checked that. The setup is good but the problem exist. About the Alps, are you using them separate or as a dual concentric? Is it posible to buy 10 Alps for me and send them to Holland? Best regards Jan Geurtsen

02.11.2005, 20:51	#5
Jan 737 Senior Member Registriert seit: 03.04.2003 Alter: 65 Beiträge: 113	Thanks Peter, Do you have a picture of it. Is it possible to connect the Alps direct to the key board? Send me your e-mail address, please. Best regards Jan Geurtsen.

Aktive Benutzer in diesem Thema: 1 (Registrierte Benutzer: 0, Gäste: 1)