[arsi]

Hallo !

Habe ein Probnlem mit meinem USB Stick!

Er wird vom Kernel erkannt und auch richtig eingebunden!

Auszug aus dmesg:
---schnitt---
usb 3-1: new high speed USB device using ehci_hcd and address 8
scsi4 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 8
usb-storage: waiting for device to settle before scanning

Vendor: OTi Model: Flash Disk Rev: 2.00
Type: Direct-Access ANSI SCSI revision: 02
sda: Unit Not Ready, sense:
: Current: sense key=0x6
ASC=0x28 ASCQ=0x0
sda : READ CAPACITY failed.
sda : status=1, message=00, host=0, driver=08
sd: Current: sense key=0x6
ASC=0x28 ASCQ=0x0
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
sda: assuming drive cache: write through
SCSI device sda: 512000 512-byte hdwr sectors (262 MB)
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
sda: assuming drive cache: write through
/dev/scsi/host4/bus0/target0/lun0: p1
Attached scsi removable disk sda at scsi4, channel 0, id 0, lun 0
usb-storage: device scan complete
---schnitt---

Auszug aus /proc/bus/usb/devices:
---schnitt---
T: Bus=03 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 8 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=0ea0 ProdID=2168 Rev= 2.00
S: Manufacturer=USB
S: Product=Flash Disk
S: SerialNumber=367118418CE6E3D2
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=200mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 2 Ivl=125us
---schnitt---

Jedoch wenn ich den Stick mounten will dann bekomm ich diese meldung:
---schnitt---
xp2600 / # mount -t vfat /dev/sda1 /mnt/usbstick
mount: wrong fs type, bad option, bad superblock on /dev/sda1,
missing codepage or other error
In some cases useful info is found in syslog - try
dmesg | tail or so

xp2600 / #
---schnitt---

fdisk -l liefert diese Ausgabe:
---schnitt---
xp2600 / # fdisk -l /dev/sda

Disk /dev/sda: 262 MB, 262144000 bytes
16 heads, 32 sectors/track, 1000 cylinders
Units = cylinders of 512 * 512 = 262144 bytes

Device Boot Start End Blocks Id System
/dev/sda1 * 1 1000 255983+ 6 FAT16
Partition 1 has different physical/logical endings:
phys=(998, 15, 32) logical=(999, 15, 31)
xp2600 / #
---schnitt---

kann mir jemand helfen???

und wie kann ich denn automount für den stick verwirklichen?


mfg Andreas