[NasenBär]

hy!

hier die ergebnisse (die mir komisch vorkamen) von dmesg:
1)
Kernel command line: auto BOOT_IMAGE=linux-secure ro root=306 devfs=mount hdc=ide-scsi acpi=ht
ide_setup: hdc=ide-scsi

wieso schreibt er bei hdc auch scsi??

2)
VP_IDE: IDE controller at PCI slot 00:07.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c596b (rev 12) IDE UDMA66 controller on pci00:07.1
ide0: BM-DMA at 0xa000-0xa007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xa008-0xa00f, BIOS settings: hdc:DMA, hdd:pio
hda: QUANTUM FIREBALL_TM1280A, ATA DISK drive
hdb: Conner Peripherals 850MB - CFS850A, ATA DISK drive
blk: queue c01a52a0, I/O limit 4095Mb (mask 0xffffffff)
blk: queue c01a53e8, I/O limit 4095Mb (mask 0xffffffff)
hdc: ST313032A, ATA DISK drive
blk: queue c01a570c, I/O limit 4095Mb (mask 0xffffffff)
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
hda: task_no_data_intr: error=0x04 { DriveStatusError }
hda: 2503872 sectors (1282 MB) w/76KiB Cache, CHS=621/64/63, DMA
hdb: attached ide-disk driver.
hdb: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
hdb: task_no_data_intr: error=0x04 { DriveStatusError }
hdb: 1664583 sectors (852 MB) w/64KiB Cache, CHS=825/32/63, DMA
Partition check:
hda: hda1 hda2 < hda5 hda6 >
hdb: hdb1
hdc:<6>end_request: I/O error, cmd 0 dev 16:00 (hdc), sector 0
end_request: I/O error, cmd 0 dev 16:00 (hdc), sector 1
end_request: I/O error, cmd 0 dev 16:00 (hdc), sector 2
end_request: I/O error, cmd 0 dev 16:00 (hdc), sector 3
end_request: I/O error, cmd 0 dev 16:00 (hdc), sector 4
end_request: I/O error, cmd 0 dev 16:00 (hdc), sector 5
end_request: I/O error, cmd 0 dev 16:00 (hdc), sector 6
end_request: I/O error, cmd 0 dev 16:00 (hdc), sector 7
end_request: I/O error, cmd 0 dev 16:00 (hdc), sector 0
end_request: I/O error, cmd 0 dev 16:00 (hdc), sector 1
end_request: I/O error, cmd 0 dev 16:00 (hdc), sector 2
end_request: I/O error, cmd 0 dev 16:00 (hdc), sector 3
end_request: I/O error, cmd 0 dev 16:00 (hdc), sector 4
end_request: I/O error, cmd 0 dev 16:00 (hdc), sector 5
end_request: I/O error, cmd 0 dev 16:00 (hdc), sector 6
end_request: I/O error, cmd 0 dev 16:00 (hdc), sector 7
end_request: I/O error, cmd 0 dev 16:00 (hdc), sector 2147483640
end_request: I/O error, cmd 0 dev 16:00 (hdc), sector 2147483641
end_request: I/O error, cmd 0 dev 16:00 (hdc), sector 2147483642
end_request: I/O error, cmd 0 dev 16:00 (hdc), sector 2147483643
end_request: I/O error, cmd 0 dev 16:00 (hdc), sector 2147483644
end_request: I/O error, cmd 0 dev 16:00 (hdc), sector 2147483645
end_request: I/O error, cmd 0 dev 16:00 (hdc), sector 2147483640
end_request: I/O error, cmd 0 dev 16:00 (hdc), sector 2147483641
end_request: I/O error, cmd 0 dev 16:00 (hdc), sector 2147483642
end_request: I/O error, cmd 0 dev 16:00 (hdc), sector 2147483643
end_request: I/O error, cmd 0 dev 16:00 (hdc), sector 2147483644
end_request: I/O error, cmd 0 dev 16:00 (hdc), sector 2147483645
end_request: I/O error, cmd 0 dev 16:00 (hdc), sector 0
end_request: I/O error, cmd 0 dev 16:00 (hdc), sector 2
end_request: I/O error, cmd 0 dev 16:00 (hdc), sector 4
end_request: I/O error, cmd 0 dev 16:00 (hdc), sector 6
end_request: I/O error, cmd 0 dev 16:00 (hdc), sector 0
end_request: I/O error, cmd 0 dev 16:00 (hdc), sector 2
end_request: I/O error, cmd 0 dev 16:00 (hdc), sector 4
end_request: I/O error, cmd 0 dev 16:00 (hdc), sector 6
ldm_validate_partition_table(): Disk read failed.
end_request: I/O error, cmd 0 dev 16:00 (hdc), sector 0
end_request: I/O error, cmd 0 dev 16:00 (hdc), sector 2
end_request: I/O error, cmd 0 dev 16:00 (hdc), sector 4
end_request: I/O error, cmd 0 dev 16:00 (hdc), sector 6
unable to read partition table
ide: late registration of driver.

??
die platte ist in einem anderen rechner vorher frisch partioniert worden (mit fdisk eine primäre dos partition erstellt) ohne probleme bzw. fehler!

hoffe mir kann wer weiterhelfen!

mfg