hallo!
ich hab jetzt mal das seatool drüberlaufen lassen! ergebnis:
PHP-Code:
-----------------------------------------------------------------
DIAGATA.EXE Version 3.07.30214ML
Copyright (c) 2002 by Seagate Technology, LLC. All rights reserved.
-----------------------------------------------------------------
Timer Resolution: 0.000122
Short Test Begin: 12-Oct-2003 23:38:47
Cable Test - 0 Errors
Buffer Test - 0 Errors
Identify Data
Model Number: ST3120026A
Serial Number: 3JT1NNZL
Firmware Revision: 3.06
Default CHS: 16383-16-63
Current CHS: 16383-16-63
Current Capacity: 16514064 Sectors
Total Capacity: 234441648 Sectors
80 Conductor Cable Reported
ID Method: CSEL
SMART Check: Passed
Outer Diameter Scan (0 to 70380) - Passed
Elapsed Time: 30.09s
Estimated Internal Transfer Rates
Min: 49.75Mb/s Max: 1711.47Mb/s Avg: 364.82Mb/s
Inner Diameter Scan (234406458 to 234441648) - Passed
Elapsed Time: 15.15s
Estimated Internal Transfer Rates
Min: 37.04Mb/s Max: 427.87Mb/s Avg: 351.78Mb/s
Random Seek (137 Cycles) - Passed
Estimated Access Times
Min: 3.051ms Max: 17.820ms Avg: 10.729ms
Random Read (137 Cycles) - Passed
Estimated Access Times
Min: 7.079ms Max: 25.754ms Avg: 15.107ms
PIO/DMA Data Compare
Total Bytes = 1224704
Estimated PIO Transfer Rates
Min: 1.54MB/s Max: 1.60MB/s Avg: 1.57MB/s
Estimated DMA Transfer Rates
Min: 21.81MB/s Max: 27.27MB/s Avg: 26.20MB/s
SMART Check: Passed
Short Test Passed: 12-Oct-2003 23:40:15
Scanning for bad sectors...
Performing Complete Surface Scan on drive: ST3120026A
Scan Completed... PROBLEMS FOUND
PHP-Code:
SeaTools Desktop v2.00.09
Copyright (c) 2003 Kroll Ontrack Inc.
10/12/2003 @ 11:43 PM
The following information has been generated by the SeaTools Desktop. Use this information to help you recognize and resolve potential data access problems in a timely manner.
System Information:
BIOS Date 07/05/01
Conventional Memory size 610 K
Extended Memory size 58532 K
IO Channel type PCI
Drive Information:
DRIVE SIZE MODEL
----- --------- ---------------------
1 120.03 GB ST3120026A
Serial Number = 3JT1NNZL
Int13 Num = 80, PHYS CHS = 14593x255x63.
ParmTable CHS, Rsvd = 14593x255x63
PARTITION CYLINDER SIZE
---------- ------------ ----
# Type Start End MB
PRIMARY
1 NTFS 0 1911 15726
EXTENDED
2 NTFS 1912 7010 41940
3 NTFS 7011 7648 5247
4 Unknown 7649 14593 57118
Diagnostic Results:
Drive 1 (ST3120026A)
SMART Status Check Result: Passed
90-Second Test Result: Passed
File Structure Test Result: Failed
(Unknown or unsupported partition(s) skipped)
Partition 1
Not Checked. Unsupported (or Unknown) Partition
Partition 2
Not Checked. Unsupported (or Unknown) Partition
Partition 3
Not Checked. Unsupported (or Unknown) Partition
Partition 4 (No Label) Result: Extended partition table invalid
Complete Surface Scan Result: Skipped
S.M.A.R.T., (S)elf (M)onitoring (A)nalysis and (R)eporting (T)echnology, a built-in hard disk drive failure prediction method reports an 'Alert' if a problem has occurred. It reports 'Passed' if no problems are found and 'Unsupported' if a hard disk drive does not support S.M.A.R.T.
******************************************
Diagnostic Summary:
System Memory Test Result: Passed
Drive 1 (ST3120026A)
SMART Status Check Result: Passed
90-Second Test Result: Passed
File Structure Test Result: Failed
(Unknown or unsupported partition(s) skipped)
Complete Surface Scan Result: Skipped
Recommendation:
If you are not experiencing data loss and SeaTools reports File System Structure errors, they may be caused by a lock-up or failure to shutdown Windows correctly. Many times, these errors may be repaired through normal system maintenance. If you are experiencing a hardware error, you should isolate the cause and replace the failing component. If you are unsure how to proceed with repairs, contact a computer professional. After completing any maintenance tasks, run SeaTools again to verify that all errors have been repaired. If errors continue to occur, the system may not be stable. Again, contact a computer professional.
SeaTools Desktop v2.00.09
Copyright (c) 2003 Kroll Ontrack Inc.
was heißt das jetzt... da hab ich anscheinend kaputte sektoren...??? was kann ich gegen die machen?
ich hab die tests bei dem bad-sector-test immer abgebrochen, weil da is es nie weitergegangen... es blieb die anzeige bei 0% und die maus hat auch beim bewegen nur mehr geruckelt! das war sowohl beim seagate als auch beim generic test so.