WCM Forum - RAID 0 + Red Hat 9.0

Jaja immer diese ATA Raids :D

Nachdem ich ja schon lang nicht bei Guru aufgetaucht bin, mal wieder ein freundliches RTFM an einen Newbie :ms:

http://www.tldp.org/HOWTO/ATA-RAID-HOWTO/
Edit: Da war flinx schneller ;)
Und das README im Treiberpaket hilft einem ja auch "nicht" :rolleyes: weiter:

Zitat:

[INSTALLATION]
Extract the contents of the TGZ file on to a formatted floppy disk.
Label the disk "FastTrak Driver Disk".
2.1 To install the FastTrak Series Linux Driver into an EXISTING SYSTEM:

1.) For RHF upgraders ONLY, append parameters
when linux booting.
Boot loader is LILO:
if graphics menu please press Ctrl-X turn to TEXT menu.
when "boot:" prompt appears press the TAB key.
append parameters see as Note 2 below.
then press enter to booting.
Boot loader is GRUB:
press 'e' when GRUB menu appears, move to the kernel line
and press 'e' to append parameters see as Note 2 below.
then press 'b' to booting.
--- OR ---
If NOT an RHF upgrader, ignore step 1 and proceed to step 2.
2.) Get driver "ft.o" from FastTrak Driver Disk by issuing commands :
# gzip -dc modules.cgz > modules.cpio
# cpio -idumv < modules.cpio
(this loads the Modules from the subdirectories which you need)
Load FastTrak Driver by issuing commands :
# insmod scsi_mod (only necessary on kernel 2.4.x, get it from
/lib/modules/..)
# insmod ft.o

2.2 To install the FastTrak Series Linux Driver into an NEW SYSTEM

1.) Start the RedHat Linux Installation with CD ROM booting.
2.) At the "Welcome to Red Hat Linux ..." installation screen, a
prompt labeled "boot:" will appear at the bottom of the screen.
3.) For RHF upgraders ONLY, please press TAB key and append parameters
(see Note 1 below).
--- OR ---
If you are NOT an RHF upgrader, type "expert" (without quotations)
or "linux dd" at the "boot:" prompt, then press the enter key.
4.) At the "Devices" dialog box, insert the FastTrak Driver Disk in the
floppy drive and then select "OK" or "Yes".
If installing RedHat 7.1/7.2, please skip to Step 9.
5.) After reaching the "Devices" dialog box again, select "Add Device".
6.) When asked "what kind of device would you like to add?", select
"SCSI", and then select "OK".
7.) Press the "P" key and scroll down to "Promise FastTrak Series ....",
and then select "OK".
8.) The installation process will now display "Promise FastTrak Series
Linux Driver" has been found. Select "Done".
9.) For RHF users ONLY, when the Boot Loader Configuration menu is displayed,
please type parameters (see NOTE 2 below) in the Kernel parameters field.
--- OR ---
If NOT an RHF user, ignore step 9 and proceed to step 10.
10.) Continue with the installation as normal.
11.) If installing RedHat 7.2 or Update Linux to RedHat 7.1/7.2.
Press Ctrl-Alt-F2 when installation at the "Congratualations" menu.
Other RedHat version please click "Exit" button to finish installation.
12.) Insert the FastTrak Driver Disk floppy, Issue commands to load FastTrak
driver.
#mount /dev/fd0 /mnt/floppy
#cd /mnt/floppy
#./setup-ft
13.) Choose your selection here, after FastTrak driver setup successful.
Please Press Ctrl-Alt-F7 and click "Exit" button to finish installation.

[NOTE]

1.) "linux ide0=0x1f0,0x3f6,14 ide1=0x170,0x376,15 ide2=0 ide3=0 ide4=0
ide5=0 ide6=0 ide7=0 ide8=0 ide9=0 expert"

2.) "ide0=0x1f0,0x3f6,14 ide1=0x170,0x376,15 ide2=0 ide3=0 ide4=0 ide5=0
ide6=0 ide7=0 ide8=0 ide9=0"