|
PC hängt sich bei rsync auf
Habe einen LINUX Server neu aufgesetzt (SUSE 10.3) und ein SW-RAID5 mit 7 Platten eingerichtet. 3 platten auf SATA 4 Platten auf einem zusätzlichen IDE Controller. Darauf habe ich den LVM gelegt mit 8 logischen Volumes. Ein fsck -f läuft ohne Fehler durch. Auf einem anderen Rechner habe ich die Daten die auf die LVs gehören. Mit rsync wollte ich diese zurück kopieren (ca. 400GB). Nach kurzer Zeit hängt sich der PC aber immer auf. Folgend die letzten Meldungen:
Apr 14 18:34:55 asterix kernel: JBD: barrier-based sync failed on dm-6 - disabling barriers Apr 14 18:40:33 asterix kernel: hdb: dma_intr: status=0x51 { DriveReady SeekComplete Error } Apr 14 18:40:33 asterix kernel: hdb: dma_intr: error=0x84 { DriveStatusError BadCRC } Apr 14 18:40:33 asterix kernel: ide: failed opcode was: unknown Apr 14 18:41:31 asterix smartd[3802]: Device: /dev/sdb, SMART Usage Attribute: 195 Hardware_ECC_Recovered changed from 52 to 53 Apr 14 18:41:31 asterix smartd[3802]: Device: /dev/sdc, SMART Usage Attribute: 195 Hardware_ECC_Recovered changed from 68 to 67 Apr 14 18:41:40 asterix syslog-ng[3608]: STATS: dropped 0 Ich finde keinen Grund warum sich der PC immer beim rsync aufhängt. Für gute Ideen wäre ich dankbar. |
bitte infos über setup des raid und ein auszug von smartctl -a /dev/sdb
die ersten 4 zeilen würden mir grund zur sorge geben, erfahrungsgemäss haben festplatten die diese kernel meldungen hervorrufen ein problem und sollten nicht mehr eingesetzt werden.... aber zuerstmal bitte ein auszug von smartctl -a /dev/sdb |
Die Platten sd[abc] vorher auf einem RAID Controller gehängt und darauf ist SUSE 9.0 gelaufen und das ohne Fehler. Jetzt ist dieser Controller ausgebaut und die Platten hängen direkt am internen IDE Controller mit SUSE 10.3. Das da jetzt auf einemal alle 3 Platten defekt sein sollen, kann ich nicht glauben.
Die restlichen 4 Platten hd[a-d] sind alle neu und auf einem neuen IDE Controller. Folgend der Output der 3 sd platten: asterix:~ # smartctl -a /dev/sda smartctl version 5.37 [i686-suse-linux-gnu] Copyright (C) 2002-6 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.10 family Device Model: ST3250820A Serial Number: 5QE11RCN Firmware Version: 3.AAD User Capacity: 250,059,350,016 bytes Device is: In smartctl database [for details use: -P show] ATA Version is: 7 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Wed Apr 16 18:52:53 2008 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 92) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 115 077 006 Pre-fail Always - 94205125 3 Spin_Up_Time 0x0003 096 095 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 116 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 087 060 030 Pre-fail Always - 562055776 9 Power_On_Hours 0x0032 089 089 000 Old_age Always - 9893 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 139 187 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0 189 Unknown_Attribute 0x003a 100 100 000 Old_age Always - 0 190 Temperature_Celsius 0x0022 057 050 045 Old_age Always - 724041771 194 Temperature_Celsius 0x0022 043 050 000 Old_age Always - 43 (Lifetime Min/Max 0/11) 195 Hardware_ECC_Recovered 0x001a 078 054 000 Old_age Always - 78524796 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0 202 TA_Increase_Count 0x0032 100 253 000 Old_age Always - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. |
asterix:~ # smartctl -a /dev/sdb
smartctl version 5.37 [i686-suse-linux-gnu] Copyright (C) 2002-6 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.10 family Device Model: ST3250820A Serial Number: 5QE11RC3 Firmware Version: 3.AAD User Capacity: 250,059,350,016 bytes Device is: In smartctl database [for details use: -P show] ATA Version is: 7 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Wed Apr 16 18:53:20 2008 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 92) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 117 085 006 Pre-fail Always - 140250148 3 Spin_Up_Time 0x0003 096 095 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 120 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 087 060 030 Pre-fail Always - 639389392 9 Power_On_Hours 0x0032 089 089 000 Old_age Always - 9848 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 167 187 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0 189 Unknown_Attribute 0x003a 100 100 000 Old_age Always - 0 190 Temperature_Celsius 0x0022 058 050 045 Old_age Always - 723976234 194 Temperature_Celsius 0x0022 042 050 000 Old_age Always - 42 (Lifetime Min/Max 0/7) 195 Hardware_ECC_Recovered 0x001a 073 046 000 Old_age Always - 164477838 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0 202 TA_Increase_Count 0x0032 100 253 000 Old_age Always - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. asterix:~ # smartctl -a /dev/sdc smartctl version 5.37 [i686-suse-linux-gnu] Copyright (C) 2002-6 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.10 family Device Model: ST3250820A Serial Number: 5QE0Z16A Firmware Version: 3.AAD User Capacity: 250,059,350,016 bytes Device is: In smartctl database [for details use: -P show] ATA Version is: 7 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Wed Apr 16 18:53:45 2008 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 92) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 119 090 006 Pre-fail Always - 231827233 3 Spin_Up_Time 0x0003 096 095 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 128 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 087 060 030 Pre-fail Always - 561318971 9 Power_On_Hours 0x0032 089 089 000 Old_age Always - 9900 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 140 187 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0 189 Unknown_Attribute 0x003a 100 100 000 Old_age Always - 0 190 Temperature_Celsius 0x0022 055 048 045 Old_age Always - 757661741 194 Temperature_Celsius 0x0022 045 052 000 Old_age Always - 45 (Lifetime Min/Max 0/11) 195 Hardware_ECC_Recovered 0x001a 062 052 000 Old_age Always - 12161419 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0 202 TA_Increase_Count 0x0032 100 253 000 Old_age Always - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. |
Zitat:
Lg. Fhmr |
hm... sorry mein fehler, interessant wäre natürlich der output von smartctl -a /dev/hdb :rolleyes:
bitte den output als code posten [ code ] und [ / code ] drumherum setzen (ohne den leerzeichen) ich habe mich von den smart meldungen irreführen lassen die aber auf die scsi/sata? verweisen, das ist nichts beunruhigendes... /dev/hdb dürfte da ein problem haben |
Ich habe auf Verdacht mal die IDE Kabel für die hd Platten getauscht. Seither läuft der PC stabil. Wundere mich zwar warum der PC nicht fsck oder beim Rebuild der RAIDs hängen geblieben ist. Muss aber nicht alles wissen.
Ich werde den PC aber die nächste Zeit noch genauer beobachten. Danke für Eure Hilfe. |
freut mich für dich das alles funktioniert, die nächste zeit aufpassen ist aber eine gute idee....
|
| Alle Zeitangaben in WEZ +2. Es ist jetzt 20:19 Uhr. |
Powered by vBulletin® Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
© 2009 FSL Verlag