Frage in der Aircraft.cfg
 

Hallo

ich habe eine Frage zu der Aircraft.cfg:
[airplane_geometry]
[airplane_geometry]
//ACM_AREAW1// 0,0,0,3.2766,1.4562,1.4562,0,3.1127,2.9125,2.9125
//ACM_AREAW2// 0,2.9489,4.3688,4.3688,0,2.7851,5.8250,5.8250,0,2. 6212
//ACM_AREAW3// 7.2813,7.2813,0,2.4574,8.7376,8.7376,0,2.2936,10.1 938,10.1938
//ACM_AREAW4// 0,2.1297,11.6501,11.6501,0,1.9659,13.1064,13.1064, 0,1.8021
//ACM_AREAH1// 0,0,0,2.8871,0.4811,0.4811,0,2.7428,0.9623,0.9623
//ACM_AREAH2// 0,2.5984,1.4435,1.4435,0,2.4540,1.9247,1.9247,0,2. 3097
//ACM_AREAH3// 2.4059,2.4059,0,2.1653,2.8871,2.8871,0,2.0210,3.36 83,3.3683
//ACM_AREAH4// 0,1.8766,3.8495,3.8495,0,1.7323,4.3307,4.3307,0,1. 5879
//ACM_AREAV1// 0,0,0,4.9514,0.5501,0.5501,0,4.5553,1.1003,1.1003
//ACM_AREAV2// 0,4.1592,1.6504,1.6504,0,3.7631,2.2006,2.2006,0,3. 3670
//ACM_AREAV3// 2.7508,2.7508,0,2.9708,3.3009,3.3009,0,2.5747,3.85 11,3.8511
//ACM_AREAV4// 0,2.1786,4.4013,4.4013,0,1.7825,4.9514,4.9514,0,1. 3864
//ACM_CAREAW1// 6.5532,6.5532,1.6383,2.2936,7.2813,7.2813,1.6383,2 .2608,8.0094,8.0094
//ACM_CAREAW2// 1.6383,2.2280,8.7376,8.7376,1.6383,2.1953,9.4657,9 .4657,1.6383,2.1625
//ACM_CAREAW3// 10.1938,10.1938,1.6383,2.1297,10.9220,10.9220,1.63 83,2.0970,11.6501,11.6501
//ACM_CAREAW4// 1.6383,2.0642,12.3782,12.3782,1.6383,2.0314,13.106 4,13.1064,1.6383,1.9987
//ACM_CAREAH1// 0,0,1.4435,2.8871,0.4811,0.4811,1.4435,2.8149,0.96 23,0.9623
//ACM_CAREAH2// 1.4435,2.7428,1.4435,1.4435,1.4435,2.6706,1.9247,1 .9247,1.4435,2.5984
//ACM_CAREAH3// 2.4059,2.4059,1.4435,2.5262,2.8871,2.8871,1.4435,2 .4540,3.3683,3.3683
//ACM_CAREAH4// 1.4435,2.3819,3.8495,3.8495,1.4435,2.3097,4.3307,4 .3307,1.4435,2.2375
//ACM_CAREAV1// 0,0,1.2378,3.7136,0.5501,0.5501,1.2378,3.5155,1.10 03,1.1003
//ACM_CAREAV2// 1.2378,3.3174,1.6504,1.6504,1.2378,3.1194,2.2006,2 .2006,1.2378,2.9213
//ACM_CAREAV3// 2.7508,2.7508,1.2378,2.7233,3.3009,3.3009,1.2378,2 .5252,3.8511,3.8511
//ACM_CAREAV4// 1.2378,2.3271,4.4013,4.4013,1.2378,2.1291,4.9514,4 .9514,1.2378,1.9310
wing_area = 894.000 // was 925
wing_span = 86.000
wing_root_chord = 9.850
wing_dihedral = -1.000
wing_incidence = 0.000
wing_twist = 0.000
oswald_efficiency_factor = 0.800
wing_winglets_flag = 0
wing_sweep = 15.000
wing_pos_apex_lon = 8.500
wing_pos_apex_vert = 0.000
htail_area = 304.000
htail_span = 28.417
htail_pos_lon = -41.000
htail_pos_vert = 0.000
htail_incidence = -1.800
htail_sweep = 0.000
vtail_area = 203.000
vtail_span = 16.245
vtail_sweep = 0.000
vtail_pos_lon = -40.000
vtail_pos_vert = 5.833
elevator_area = 96.000
aileron_area = 36.960
rudder_area = 34.5
elevator_up_limit = 25.5
elevator_down_limit = 21.5
aileron_up_limit = 19.5
aileron_down_limit = 14.5
rudder_limit = 23.5
elevator_trim_limit = 8.5
spoiler_limit = 60.0
aileron_to_spoileron_gain = 3.000
min_ailerons_for_spoilerons = 9.969
min_flaps_for_spoilerons = 0.000
spoilerons_available = 0

Was bedeuten diese ACM am Anfang? Haben sie einen effekt?

Gruß
chris

Nein.Alle Einträge wo sich // davor befindet sind nur Erklärungshinweise.Das ACM deutet darauf hin,das die Einträge mit dem Bearbeitungstool ACM Aircraft Container Manager bearbeitet wurden.
Die Zahlen tippe ich mal,dass das die Koordinatenpunkte,vom CoG ausgehend sind,über die die zweidimensionale Geometrie der Flächen,Leitwerke und Ruder ermittelt wurde.Genau weiß ich das aber nicht,weil icht keine registrierte Version von ACM besitze und deshalb die aircraft.cfg damit nicht bearbeiten kann.

Hallo

Danke erstmal, eine Frage hab ich aber noch:
Was bedeutet unter [contact_points] der Eintrag:static_pitch=-1.099